ParkZone ICON A5 PNP Bedienerhandbuch PDF herunterladen (Seite 4)

ENEN

Charging the Flight Battery

The Battery Charging Process

1. Charge only batteries that are cool to the touch and are not damaged. Look at the battery to make sure it is not damaged e.g., swollen, bent, broken

or punctured.

2. Attach the input cord of the charger to the appropriate power supply (12V accessory outlet).

3. When the Li-Po charger has been correctly powered up, there will be an approximate 3-second delay, then an audible “beep” and the green (ready) LED

will ﬂ ash.

4. Turn the control on the Amps selector so the arrow points to the charging rate required for the Battery (the ICON A5 2200mAh Li-Po battery will charge at

2.0 amps). DO NOT change the charge rate once the battery begins charging.

5. Move the cell selector switch to 3-cell for your battery.

6. Connect the Balancing Lead of the Battery to the 3-cell (it has 4 pins) charger port.

7. The green and red LEDs may ﬂ ash during the charging process when the charger is balancing cells. Balancing prolongs the life of the battery.

8. When the battery is fully charged, there will be an audible beep for about 3 seconds and the green LED will shine continuously. Attempting to charge an

over-discharged battery will cause the charger to repeatedly ﬂ ash and beep, indicating an error has occurred.

9. Always unplug the battery from the charger immediately upon completion of charging.

CAUTION: Overcharging a battery can cause a ﬁ re.

When a Li-Po battery is discharged below 3V per cell, it will not hold a charge.

The ESC protects the ﬂ ight battery from over-discharge using Low Voltage

Cutoff (LVC). Before the battery charge decreases too much, LVC removes

power supplied to the motor. Power to the motor pulses, showing that some

battery power is reserved for ﬂ ight control and safe landing.

When the motor pulses, land the aircraft immediately and recharge the

ﬂ ight battery. Disconnect and remove the Li-Po battery from the aircraft after

use to prevent trickle discharge. Fully charge your Li-Po battery before storing

it. During storage, make sure battery charge does not go below 3V per cell.

Your ICON A5 comes with a DC balancing charger and 3S Li-Po battery. You

should only charge the battery with the included charger. Never leave the bat-

tery and charger unattended during the charge process. Failure to follow the

instructions properly could result in a ﬁ re. When charging, make certain the

battery is on a heat-resistant surface. Charge the ﬂ ight battery while assembling

the aircraft. Install the fully charged battery to perform control tests and binding.

DC Li-Po Balancing Charger Features

• Charges 2- to 3-cell lithium polymer battery packs

• Variable charge rates from 300mAh to 2-amp

• Simple single push-button operation

• LED charge status indicator

• LED cell balance indicator

• Audible beeper indicates power and charge status

• 12V accessory outlet input cord

Speciﬁ cations

• Input power: 12V DC, 3-amp

• Charges 2- to 3-cell Li-Po packs with minimum capacity of 300mAh

3S 11.1V 2200mAh 25C Li-Po Battery Pack (PKZ1029)

The ParkZone

3S Li-Po battery pack features a balancing lead that allows

you to safely charge your battery pack when used with the included ParkZone

Li-Po balancing charger.

CAUTION: The balance connector must be inserted into the correct port

of your charger prior to charging.

Low Voltage Cutoff (LVC)

CAUTION: Only use a charger speciﬁ cally designed to charge a Li-Po

battery. Failure to do so could result in ﬁ re causing injury or property

damage.

CAUTION: Never exceed the recommended charge rate.

NOTICE: If using a battery other than the included Li-Po battery, refer to your

battery manufacturer’s instructions for charging.

1 2 3 4 5 6 7 8 9 ... 18 19

Kommentare zu diesen Handbüchern

Keine Kommentare

ParkZone ICON A5 PNP Bedienerhandbuch Seite 4

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ferngesteuertes Spielzeug ParkZone ICON A5 PNP